What Is Contract Demand in Msedcl

In September last year, the Delhi Electricity Regulatory Commission cut fixed costs for industrial and non-domestic consumers by 50 percent. The Commission Communication stated that during the lock-up period (until 30 May 2020), several C&I entities had not exhausted their contractually agreed capacities. Due to the constant increase in the price of electricity, all types of customers must find new formulas to reduce their electricity bills. To do this, we present our new power management system to control maximum demand: MDC series (MDC 4 and MDC 20). In a recently issued order, the Maharashtra Electricity Regulatory Commission (MERC) approved contract demand revisions up to twice for commercial and industrial (C&I) high voltage (HV) consumers and up to an opportunity for low voltage C&I (LT) consumers in a billing cycle until March 31, 2022. However, Adani Electricity Mumbai Limited said in its response that the entire country, as well as the state of Maharashtra, are currently suffering from the second wave of the Covid-19 pandemic and that the lockdown has resulted in the closure of most facilities in the non-essential category. Given these factors, the company stated that it had no objection to the Commission`s request for an extension of the previous order, so the contract application could be amended. Dispute Resolution: If a dispute or difference of any kind arises between the parties (“Dispute”) in connection with or outside this Agreement or as a result of the breach, termination or invalidity of the Agreement, the Consumer agrees to resolve the Dispute through mutual discussions, otherwise the Consumer will refer these disputes to the Consumer Complaint Resolution Forum established by the Distributor for redress. sponsor. The contract requirement is the amount of electricity (kW) that a customer requests from the distribution undertaking (DISCOM) within a certain period of time. For the specific case of Spain, depending on the maximum value of the request, the penalty may include a very large bill increase, as described in the following graph: The maximum value of the request is the average of the instantaneous power (in kW or kVA) for a defined time interval, usually every 15 minutes (this time interval depends on each country). There are several methods to calculate this parameter: to avoid penalties for the maximum demand, we must ensure that this value never exceeds the contractual performance.

MSEDCL added in its response that the Commission`s previous order was due to the difficulties faced by the industry due to the drop in demand. The current situation was different as demand returned to normal. Maximum duration of consumption The increase exceeds depending on the service contracted (Spain – for tariffs 3.0 and 3.1) Consequently, the Commission considered it appropriate to allow changes to the contractual request twice during a billing month for consumers excluding VAT C&I. Similarly, the LT consumer can only revise the contract application once per billing month. The main objective of the new CIRCUTOR MDC series is to manage and control the maximum demand of an installation. To achieve this goal, the device connects and disconnects certain (non-critical) loads to ensure that the maximum demand is never greater than the contracted power, thus avoiding surprises in the electricity bill. In addition, the extended MDC 20 series allows tariff control to adjust charges for connection in lower price periods, thus avoiding high consumption due to the simultaneity of charges during periods of high tariff prices. This is the calculation of the maximum demand for a defined interval (usually every 15 minutes).

Once the data is recovered, one minute wait to start a new calculation of 15 minutes (this time may vary depending on the country). This means that every minute (this time may depend on the meter), a maximum demand value of the last 15-minute period is recorded. These 60 registers are measured every hour. New MDC series for control and control of maximum demand This is the calculation of the maximum demand for a defined interval (usually every 15 minutes). Once the data is recovered, the value is saved and a reset is performed to start a new calculation for the next 15 minutes. These 4 registers are measured every hour. The Commission found that, given the current pandemic circumstances, consumers needed flexibility to revise their contractual application for a longer period of time. The number of opportunities allowed in previous practice directions also had to be changed to change circumstances. As described below, allows us to optimally manage contractual performance: the Commission found that for consumers in open access in the short term, a review of the contractual demand during the open access period would not be allowed. In addition, consumers of open access in the medium and long term should request the revision of open access rights in accordance with their planned revised contractual request.

In addition, MDC 4 has an internal power analyzer to calculate the maximum demand (it also records electrical parameters such as voltage, current and power). Whenever the MDC 4 detects excess power, multiple lines with non-critical loads are disconnected, automatically reducing instantaneous power. This ensures that the system does not exceed the maximum demand limit and thus avoids penalties for the next electricity bill. Kalika Steel Alloys and 27 others had submitted a petition to the Commission calling for a revision of the Treaty. They requested an extension of the Commission`s previous order, which allowed for several changes in the contract application given the disruptions caused by the Covid-19 pandemic. As we have progressed, the objective of maximum demand control is not to exceed the contractually agreed service limit. To archive this goal, we recommend that you install a system that can separate non-critical loads over different periods of time and avoid connecting loads at the same time to reduce current performance. .